PRO30-1U_KUD +V5V +24V

PRT Model No. PRO30-1U Customer Part No.

CONTENT

1. Specifications …………………………………………………………….. Page 1~2

2. User’s manual……………………………………………………………. Page 3

3. Outline dimensions………………………………………………………. Page4

4. Label diagram……………………………………………………………..Page5

History List

Rev. Date A0 2008-11-12

Explain Issue

Note

PRT

Model No. PRO30-1U Customer Part No.

1. Electrical Characteristics: Items Specification Remarks 1.1 Input: 1.1.1 Input Range Voltage 1.1.3 Efficiency 1.1.4 Inrush Current 1.2 Input Protection: 1.2.1 Over-current 1.3 Output: 1.3.1 Output Voltage 1.3.2 Output Current 1.3.3 Output Power 1.3.4 Line Regulation 1.3.5 Load Regulation 1.3.6 Ripple + Noise

100Vac(min)~240Vac(max) 70% min. 30A max.

Input power is off by a fuse 5V±15%, 24V±15% 0A~0.5A for 5V output 0A~1.0A for 24V output Total Power 26.5W Max. 5% max. 10% max.

100mV max. for 5V output, 240mV max. for 24V output

At full load and within input voltage 100~240V At Vin=230Vac

Fuse ratings 2.5A/250Vac

Oscilloscope bandwidth=20MHz, 47uF/50V electrolytic and

0.1uF/50V ceramic capacitors are connected at output. At Vin=100Vac/60Hz

Increase load current gradually until the output is shorted or burst.

Over the operating temperature range.

1.1.2 Input Range Frequency 50Hz(min)~60Hz(max) 1.3.7 Rise Time 1.4 Output Protection: 1.4.1 Over-load

1S max.

No odor, smoke, fire, plastic deformation, and excessive heat happen.

No odor, smoke, fire, plastic deformation, and excessive heat happen.

1.4.2 Short-circuit

1.5 Safety Standard: UL/cUL (UL60950-1) TUV, CB (EN60950-1)

Approved by

Kevin chen

Checked by

Yon Tsing Prepared by

LOIS Page 1

PRT

1.6 EMC Standard: 1.6.1 EMI

Model No. PRO30-1U Customer Part No.

CE EN55022

FCC Part 15

1500Vac/5mA/1 minute or 2121Vdc/5mA/1 minute

Class A

The voltage applied to the

insulation under test is gradually raised from zero to the prescribed voltage and held at that value for 60s.

At Vin=254Vac At full load 25℃

1.7 Others: 1.7.1 Dielectric Withstanding

Voltage

(Primary to secondary)

1.7.2 Leakage Current 1.7.3 M.T.B.F

0.35mA 60000 hours

2. Mechanical Characteristics: 2.1 Dimension 2.2 AC input connector 2.3 Output connector

43.4 x 69 x 28mm White- nature, Black- Live Yellow wire- +24V Red wire- +5V Black wire- GND As shown on label diagram Damaged, or rusted surface is not permitted

Frequency=10-55-10Hz, Amplitude 1.5mm, X-Y-Z direction, 30 minutes each direction

Under non-operating status, meet specification after test Width x Depth x Height As shown in figure 1 As shown in figure 1 2.4 Connector Polarity 2.5 Surface 2.6 Vibration Test

3. Environmental Characteristics: 3.1 Storage Temperature -20 to +60oC Range 3.2 Operating Temperature

Range

0 to +40oC 5 to 95% 20 to 90% 40±5 oC, 4 hours

RH: Relative Humidity

Each unit before shipping, full

load at Vin=220Vac

Yon Tsing

Prepared by

LOIS Page 2

3.3 Storage RH Range 3.4 Operating RH Range 3.5 Burn-in

Approved by

Kevin chen

Checked by

PRT

Model No. PRO30-1U Customer Part No.

User’s Manual

MODEL NO.: PRO30-1U

1.) Operate the power supply only on maximum ambient temperature 40℃.

2.) The switching power supply shall be installed according to specification. The current of load

and output power shall be not over the specified as following value. Output Rating:

Model No

PRO30-1U

3.) The power supply is a building-in component. During installation into a certain equipment,

the relevant requirement of EN 60 950-1/IEC 60950-1, UL 60950-1 and CSA C22.2 No. 60950-1 shall be maintained.

4.) The creepage distance, clearance and thickness of insulation into a certain primary and

ground as well as primary and secondary circuits shall comply with the current requirement of EN 60950-1/IEC 60950-1, UL 60950-1

5.) The switching power supply for ITE or relevant equipment use only.

6.) Output polarity:

Yellow wire- +24V Red wire- +5V Black wire- GND

Approved by

Kevin chen

Checked by

Yon Tsing

Prepared by

LOIS Page 3

Output Voltage

(Vdc)

Output Current

(A)

Output Watts

(W)

+5V 0-0.5A +24V 0-1.0A Total 26.5W PRT Model No. PRO30-1U Customer Part No. Outline dimensions (Unit: mm) Figure 1 Note: Tolerance x.x ±0.20 x.xx ±0.10 Approved by Kevin chen Checked by Yon Tsing Prepared by LOIS Page 4 PRT Model No. PRO30-1U Customer Part No. Label diagram (Unit: mm) 37PRT45SWITCHING POWER SUPPLYMODEL NO. : PRO30-1UINPUT:100 - 240V~ 50/60Hz 0.4A Max.OUTPUT: 5.0V 0-0.5A24.0V 0-1.0A TOTAL 26.5WWARNING!HAZARDOUS VOLTAGES CONTAINED WITHIN.THIS POWER SUPPLY, NOT USER SERVICEABLE.RETURN TO SERVICE CENTER FOR REPAIR.For dry location use only. Nur fur Innenraume geeignetRPRODUCT SERVICEBauart..geruftE 178722Output: Yellow wire(+24V), Red wire(+5V), Black wire(GND)MADE IN CHINA Notes: 1. Thickness: 0.27mm min., inflammation classes 94V-2 or better. 2. Color: Silver background with Black letters. 3. Tolerance: ±0.2mm Approved by Kevin chen Checked by Yon Tsing Prepared by LOIS Page 5